 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| White Electronic Designs 64Mx72 DDR SDRAM FEATURES Data rate = 200, 250, 266 and 333Mbs Package: * 219 Plastic Ball Grid Array (PBGA), 25 x 32mm 2.5V 0.2V core power supply 2.5V I/O (SSTL_2 compatible) Differential clock inputs (CK and CK#) Commands entered on each positive CK edge Internal pipelined double-data-rate (DDR) architecture; two data accesses per clock cycle Programmable Burst length: 2,4 or 8 Bidirectional data strobe (DQS) transmitted/ received with data, i.e., source-synchronous data capture (one per byte) DQS edge-aligned with data for READs; centeraligned with data for WRITEs DLL to align DQ and DQS transitions with CK Four internal banks for concurrent operation Data mask (DM) pins for masking write data (one per byte) Programmable IOL/IOH option Auto precharge option Auto Refresh and Self Refresh Modes Commercial, Industrial and Military TemperatureRanges Organized as 64M x 72 Weight: W3E64M72S-XBX - 4.5 grams typical W3E64M72S-XBX ADVANCED* BENEFITS 66% Space Savings vs. TSOP Reduced part count 55% I/O reduction vs TSOP Reduced trace lengths for lower parasitic capacitance Suitable for hi-reliability applications Laminate interposer for optimum TCE match GENERAL DESCRIPTION The 512MByte (4Gb) DDR SDRAM is a high-speed CMOS, dynamic random-access, memory using 9 chips containing 536,870,912 bits. Each chip is internally configured as a quad-bank DRAM. The 512MB DDR SDRAM uses a double data rate ar chi tec ture to achieve high-speed operation. The double data rate architecture is essentially a 2n-prefetch architecture with an interface designed to transfer two data words per clock cycle at the I/O pins. A single read or write access for the 512MB DDR SDRAM effectively consists of a single 2n-bit wide, one-clock-cycle data tansfer at the internal DRAM core and two corresponding n-bit wide, one-half-clock-cycle data transfers at the I/O pins. A bi-directional data strobe (DQS) is transmitted externally, along with data, for use in data capture at the receiver.strobe transmitted by the DDR SDRAM during READs and by the memory contoller during WRITEs. DQS is edge-aligned with data for READs and center-aligned with data for WRITEs. Each chip has two data strobes, one for the lower byte and one for the upper byte. The 512MB DDR SDRAM operates from a differential clock (CK and CK#); the crossing of CK going HIGH and CK# going LOW will be referred to as the positive edge of CK. Commands (address and control signals) are registered at every positive edge of CK. Input data is registered on both edges of DQS, and output data is referenced to both edges of DQS, as well as to both edges of CK. * This product is under development, is not qualified or characterized and is subject to change or cancellation without notice. White Electronic Designs Corp. reserves the right to change products or specifications without notice. June 2005 Rev. 0 1 White Electronic Designs Corporation * (602) 437-1520 * www.wedc.com White Electronic Designs DENSITY COMPARISONS ACTUAL SIZE W3E64M72S-XBX ADVANCED White Electronic Designs W3E64M72S-XBX 25 32 Area = 800mm2 I/O Count = 219 Balls SAVINGS - Area: 66% - I/O Count: 55% Discrete Approach 11.9 11.9 11.9 11.9 11.9 11.9 11.9 11.9 11.9 22.3 54 TSOP 54 TSOP 54 TSOP 54 TSOP 54 TSOP 54 TSOP 54 TSOP 54 TSOP 54 TSOP Area: 9 x 265mm2 = 2,385mm2 Read and write accesses to the DDR SDRAM are burst oriented; accesses start at a selected location and continue for a programmed number of locations in a programmed sequence. Accesses begin with the registration of an ACTIVE command, which is then followed by a READ or WRITE command. The address bits registered coincident with the ACTIVE command are used to select the bank and row to be accessed. The address bits registered coincident with the READ or WRITE command are used to select the bank and the starting column location for the burst access. The DDR SDRAM provides for programmable READ or WRITE burst lengths of 2, 4, or 8 locations. An auto precharge function may be enabled to provide a selftimed row precharge that is initiated at the end of the burst access. The pipelined, multibank architecture of DDR SDRAMs allows for concurrent operation, thereby providing high effective bandwidth by hiding row precharge and activation time. An auto refresh mode is provided, along with a powerJune 2005 Rev. 0 I/O Count: 9 x 54 pins = 486 pins saving power-down mode. All inputs are compatible with the Jedec Standard for SSTL_2. All full drive options outputs are SSTL_2, Class II compatible. FUNCTIONAL DESCRIPTION Read and write accesses to the DDR SDRAM are burst oriented; accesses start at a selected location and continue for a programmed number of locations in a programmed sequence. Accesses begin with the registration of an ACTIVE command which is then followed by a READ or WRITE command. The address bits registered coincident with the ACTIVE command are used to select the bank and row to be accessed (BA0 and BA1 select the bank, A0-12 select the row). The address bits registered coincident with the READ or WRITE command are used to select the starting column location for the burst access. Prior to normal operation, the DDR SDRAM must be initialized. The following sections provide detailed information covering device initialization, register definition, command descriptions and device operation. White Electronic Designs Corp. reserves the right to change products or specifications without notice. 2 White Electronic Designs Corporation * (602) 437-1520 * www.wedc.com White Electronic Designs FIGURE 1 - PIN CONFIGURATION W3E64M72S-XBX ADVANCED Top View 1 A B C D E F G H J K L M N P R T DQ1 2 DQ0 3 DQ14 4 DQ15 5 VSS 6 VSS 7 A9 8 A10 9 10 A11 A8 11 12 13 14 15 16 VCCQ VCCQ DQ16 DQ17 DQ31 VSS DQ2 DQ12 DQ13 VSS VSS A0 A7 A6 A1 VCC VCC DQ18 DQ19 DQ29 DQ30 DQ3 DQ4 DQ10 DQ11 VCC VCC A2 A5 A4 A3 VSS VSS DQ20 DQ21 DQ27 DQ28 DQ6 DQ5 DQ8 DQ9 VCCQ VCCQ A12 DNU DNU DNU VSS VSS DQ22 DQ23 DQ26 DQ25 DQ7 DQML0 VCC DQMH0 DQSH3 DQSL0 DQSH0 BA0 BA1 DQSL1 DQSH1 VREF DQML1 VSS NC DQ24 CAS0# WE0# VCC CLK0 DQSL3 RAS1# WE1# VSS DQMH1 CLK1 CS0# RAS0# VCC CKE0 CLK0# CAS1# CS1# VSS CLK1# CKE1 VSS VSS VCC VCCQ VSS VCC VSS Vss VCCQ VCC VSS VSS VCC VCCQ VSS VCC VSS VSS VCCQ VCC CLK3# CKE3 VCC CS3# DQSL4 CLK2# CKE2 VSS RAS2# CS2# NC CLK3 VCC CAS3# RAS3# DQSL2 CLK2 VSS WE2# CAS2# DQ56 DQMH3 VCC WE3# DQML3 CKE4 NC CLK4 CAS4# WE4# RAS4# CS4# DQMH2 VSS DQML2 DQ39 DQ57 DQ58 DQ55 DQ54 NC CLK4# NC NC DQ71 DQ70 DQML4 DQSH2 DQ41 DQ40 DQ37 DQ38 DQ60 DQ59 DQ53 DQ52 VSS VSS NC NC DQ69 DQ68 VCC VCC DQ43 DQ42 DQ36 DQ35 DQ62 DQ61 DQ51 DQ50 VCC VCC NC NC DQ67 DQ66 VSS VSS DQ45 DQ44 DQ34 DQ33 VSS DQ63 DQ49 DQ48 VCCQ VCCQ NC NC DQ65 DQ64 VSS VSS DQ47 DQ46 DQ32 VCC NOTE: DNU = Do Not Use. White Electronic Designs Corp. reserves the right to change products or specifications without notice. June 2005 Rev. 0 3 White Electronic Designs Corporation * (602) 437-1520 * www.wedc.com White Electronic Designs FIGURE 2 - FUNCTIONAL BLOCK DIAGRAM W3E64M72S-XBX ADVANCED WE0# RAS0# CAS0# WE# RAS# CAS# A0-12 DQ0 BA0-1 WE# RAS# CAS# A0-12 DQ0 BA0-1 A0-12 BA0-1 DQ0 DQ8 CK0 CK0# CKE0 CS0# DQML0 DQSL0 WE1# RAS1# CAS1# CK CK# CKE CS# DQML DQS IC0 DQ7 DQ7 CK0 CK0# CKE0 CS0# DQMH0 DQSH0 CK CK# CKE CS# DQM DQS IC5 DQ7 DQ15 WE# RAS# CAS# A0-12 BA0-1 DQ0 DQ16 WE# RAS# CAS# A0-12 BA0-1 DQ0 DQ24 CK1 CK1# CKE1 CS1# DQML1 DQSL1 WE2# RAS2# CAS2# CK CK# CKE CS# DQM DQS IC1 DQ7 DQ23 CK1 CK1# CKE1 CS1# DQMH1 DQSH1 CK CK# CKE CS# DQM DQS IC6 DQ7 DQ31 WE# RAS# CAS# A0-12 BA0-1 DQ0 DQ32 WE# RAS# CAS# A0-12 BA0-1 DQ0 DQ40 CK2 CK2# CKE2 CS2# DQML2 DQSL2 WE3# RAS3# CAS3# CK CK# CKE CS# DQM DQS IC2 DQ7 DQ39 CK2 CK2# CKE2 CS2# DQMH2 DQSH2 CK CK# CKE CS# DQM DQS IC7 DQ7 DQ47 WE# RAS# CAS# A0-12 BA0-1 DQ0 DQ48 WE# RAS# CAS# A0-12 BA0-1 DQ0 DQ56 CK3 CK3# CKE3 CS3# DQML3 DQSL3 WE4# RAS4# CAS4# CK CK# CKE CS# DQM DQS IC3 DQ7 DQ55 CK3 CK3# CKE3 CS3# DQMH3 DQSH3 CK CK# CKE CS# DQM DQS IC8 DQ7 DQ63 WE# RAS# CAS# A0-12 DQ0 BA0-1 DQ64 CK4 CK4# CKE4 CS4# DQML4 DQSL4 CK CK# CKE CS# DQM DQS IC4 DQ7 DQ71 White Electronic Designs Corp. reserves the right to change products or specifications without notice. June 2005 Rev. 0 4 White Electronic Designs Corporation * (602) 437-1520 * www.wedc.com White Electronic Designs INITIALIZATION DDR SDRAMs must be powered up and initialized in a predefined manner. Operational procedures other than those specified may result in undefined operation. Power must first be applied to VCC and VCCQ simultaneously, and then to VREF (and to the system VTT). VTT must be applied after VCCQ to avoid device latch-up, which may cause permanent damage to the device. VREF can be applied any time after VCCQ but is expected to be nominally coincident with VTT. Except for CKE, inputs are not recognized as valid until after VREF is applied. CKE is an SSTL_2 input but will detect an LVCMOS LOW level after VCC is applied. After CKE passes through VIH, it will transition to an SSTL_2 signal and remain as such until power is cycled. Maintaining an LVCMOS LOW level on CKE during powerup is required to ensure that the DQ and DQS outputs will be in the High-Z state, where they will remain until driven in normal operation (by a read access). After all power supply and reference voltages are stable, and the clock is stable, the DDR SDRAM requires a 200s delay prior to applying an executable command. Once the 200s delay has been satisfied, a DESELECT or NOP command should be applied, and CKE should be brought HIGH. Following the NOP command, a PRECHARGE ALL command should be applied. Next a LOAD MODE REGISTER command should be issued for the extended mode register (BA1 LOW and BA0 HIGH) to enable the DLL, followed by another LOAD MODE REGISTER command to the mode register (BA0/BA1 both LOW) to reset the DLL and to program the operating parameters. Two-hundred clock cy cles are required between the DLL reset and any READ command. A PRECHARGE ALL command should then be applied, placing the device in the all banks idle state. Once in the idle state, two AUTO REFRESH cycles must be performed (tRFC must be satisfied.) Additionally, a LOAD MODE REGISTER command for the mode register with the reset DLL bit deactivated (i.e., to program operating pa ram e ters without resetting the DLL) is required. Following these requirements, the DDR SDRAM is ready for normal operation. W3E64M72S-XBX ADVANCED REGISTER DEFINITION MODE REGISTER The Mode Register is used to define the specific mode of operation of the DDR SDRAM. This definition includes the selection of a burst length, a burst type, a CAS latency, and an operating mode, as shown in Figure 3. The Mode Register is programmed via the MODE REGISTER SET command (with BA0 = 0 and BA1 = 0) and will retain the stored information until it is programmed again or the device loses power. (Except for bit A8 which is self clearing). Reprogramming the mode register will not alter the contents of the memory, provided it is performed correctly. The Mode Register must be loaded (reloaded) when all banks are idle and no bursts are in progress, and the controller must wait the specified time before initiating the subsequent operation. Violating either of these requirements will result in unspecified operation. Mode register bits A0-A2 specify the burst length, A3 specifies the type of burst (sequential or interleaved), A4-A6 specify the CAS latency, and A7-A12 specify the operating mode. BURST LENGTH Read and write accesses to the DDR SDRAM are burst oriented, with the burst length being programmable, as shown in Fig ure 3. The burst length determines the maximum number of column locations that can be accessed for a given READ or WRITE command. Burst lengths of 2, 4 or 8 locations are available for both the sequential and the interleaved burst types. Reserved states should not be used, as unknown operation or incompatibility with future versions may result. When a READ or WRITE command is issued, a block of columns equal to the burst length is effectively selected. All accesses for that burst take place within this block, meaning that the burst will wrap within the block if a boundary is reached. The block is uniquely selected by A1-Ai when the burst length is set to two; by A2-Ai when the burst length is set to four (where Ai is the most significant column address for a given configuration); and by A3-Ai when the burst length is set to eight. The remaining (least significant) address bit(s) is (are) used to select the starting location within the block. The programmed burst length applies to both READ and WRITE bursts. White Electronic Designs Corp. reserves the right to change products or specifications without notice. June 2005 Rev. 0 5 White Electronic Designs Corporation * (602) 437-1520 * www.wedc.com White Electronic Designs BURST TYPE Accesses within a given burst may be programmed to be either sequential or interleaved; this is referred to as the burst type and is selected via bit M3. The ordering of accesses within a burst is determined by the burst length, the burst type and the starting column address, as shown in Table 1. W3E64M72S-XBX ADVANCED via the LOAD MODE REGISTER command to the mode register (with BA0 = 1 and BA1 = 0) and will retain the stored information until it is programmed again or the device loses power. The enabling of the DLL should always be followed by a LOAD MODE REGISTER command to the mode register (BA0/BA1 both LOW) to reset the DLL. The extended mode register must be loaded when all banks are idle and no bursts are in progress, and the controller must wait the specified time before initiating any sub se quent operation. Violating either of these requirements could result in unspecified operation. READ LATENCY The READ latency is the delay, in clock cycles, between the registration of a READ command and the availability of the first bit of output data. The latency can be set to 2, 2.5, or 3 clocks. If a READ command is registered at clock edge n, and the latency is m clocks, the data will be available by clock edge n+m. Table 2 below indicates the operating frequencies at which each CAS latency setting can be used. Reserved states should not be used as unknown operation or incompatibility with future versions may result. TABLE 2 - CAS LATENCY ALLOWABLE OPERATING FREQUENCY (MHz) SPEED -200 -250 -266 -333* CAS LATENCY = 2 CAS LATENCY = 2.5 CAS LATENCY = 3 75 100 -- 100 125 -- 100 133 -- 100 133/ 166 166 * For 333Mbs operation of Industrial and commercial temperatures CL = 2.5, at Military temperature CL = 3. OPERATING MODE The normal operating mode is selected by issuing a MODE REGISTER SET command with bits A7-A12 each set to zero, and bits A0-A6 set to the desired values. A DLL reset is initiated by issuing a MODE REGISTER SET command with bits A7 and A9-A12 each set to zero, bit A8 set to one, and bits A0-A6 set to the desired values. Although not required, JEDEC specifications recommend when a LOAD MODE REGISTER command is issued to reset the DLL, it should always be followed by a LOAD MODE REGISTER command to select normal operating mode. All other combinations of values for A7-A12 are reserved for future use and/or test modes. Test modes and reserved states should not be used because unknown operation or incompatibility with future versions may result. OUTPUT DRIVE STRENGTH The normal full drive strength for all outputs are specified to be SSTL2, Class II. DLL ENABLE/DISABLE When the part is running without the DLL enabled, device functionality may be altered. The DLL must be enabled for normal operation. DLL enable is required during powerup initialization and upon returning to normal operation after having disabled the DLL for the purpose of debug or evaluation. (When the device exits self refresh mode, the DLL is enabled automatically.) Any time the DLL is enabled, 200 clock cycles with CKE high must occur before a READ command can be issued. EXTENDED MODE REGISTER The extended mode register controls functions beyond those controlled by the mode register; these additional functions are DLL enable/disable, output drive strength, and QFC. These functions are controlled via the bits shown in Figure 5. The extended mode register is programmed White Electronic Designs Corp. reserves the right to change products or specifications without notice. June 2005 Rev. 0 6 White Electronic Designs Corporation * (602) 437-1520 * www.wedc.com White Electronic Designs COMMANDS The Truth Table provides a quick reference of available commands. This is followed by a written description of each command. W3E64M72S-XBX ADVANCED WRITE The WRITE command is used to initiate a burst write access to an active row. The value on the BA0, BA1 inputs selects the bank, and the address provided on inputs A0-9, 11 selects the starting column location. The value on input A10 determines whether or not AUTO PRECHARGE is used. If AUTO PRECHARGE is selected, the row being accessed will be precharged at the end of the WRITE burst; if AUTO PRECHARGE is not selected, the row will remain open for subsequent accesses. Input data appearing on the DQ is written to the memory array subject to the DQM input logic level appearing coincident with the data. If a given DQM signal is registered LOW, the corresponding data will be written to memory; if the DQM signal is registered HIGH, the corresponding data inputs will be ignored, and a WRITE will not be executed to that byte/column location. DESELECT The DESELECT function (CS# High) prevents new commands from being executed by the DDR SDRAM. The SDRAM is effectively deselected. Operations already in progress are not affected. NO OPERATION (NOP) The NO OPERATION (NOP) command is used to perform a NOP to the selected DDR SDRAM (CS# is LOW while RAS#, CAS#, and WE# are high). This prevents unwanted commands from being registered during idle or wait states. Operations already in progress are not affected. LOAD MODE REGISTER The Mode Registers are loaded via inputs A0-12. The LOAD MODE REGISTER command can only be issued when all banks are idle, and a subsequent executable command cannot be issued until tMRD is met. PRECHARGE The PRECHARGE command is used to deactivate the open row in a particular bank or the open row in all banks. The bank(s) will be available for a subsequent row access a specified time (tRP) after the PRECHARGE command is issued. Except in the case of concurrent auto precharge, where a READ or WRITE command to a different bank is allowed as long as it does not interrupt the data transfer in the current bank and does not violate any other timing parameters. Input A10 determines whether one or all banks are to be precharged, and in the case where only one bank is to be precharged, inputs BA0, BA1 select the bank. Otherwise BA0, BA1 are treated as "Don't Care." Once a bank has been precharged, it is in the idle state and must be activated prior to any READ or WRITE commands being issued to that bank. A PRECHARGE command will be treated as a NOP if there is no open row in that bank (idle state), or if the previously open row is already in the process of precharging. ACTIVE The ACTIVE command is used to open (or activate) a row in a particular bank for a subsequent access. The value on the BA0, BA1 inputs selects the bank, and the address provided on inputs A0-12 selects the row. This row remains active (or open) for accesses until a PRECHARGE com mand is issued to that bank. A PRECHARGE command must be issued before opening a different row in the same bank. READ The READ command is used to initiate a burst read access to an active row. The value on the BA0, BA1 inputs selects the bank, and the address provided on inputs A0-9, 11 selects the starting column location. The value on input A10 determines whether or not AUTO PRECHARGE is used. If AUTO PRECHARGE is selected, the row being accessed will be precharged at the end of the READ burst; if AUTO PRECHARGE is not selected, the row will remain open for subsequent accesses. AUTO PRECHARGE AUTO PRECHARGE is a feature which performs the same individual-bank PRECHARGE function described above, but without requiring an explicit command. This is accomplished by using A10 to enable AUTO PRECHARGE in conjunction with a specific READ or WRITE command. A precharge of the bank/row that is addressed with the READ or WRITE command is automatically performed upon completion of the READ or WRITE burst. AUTO White Electronic Designs Corp. reserves the right to change products or specifications without notice. June 2005 Rev. 0 7 White Electronic Designs Corporation * (602) 437-1520 * www.wedc.com White Electronic Designs FIGURE 3 - MODE REGISTER DEFINITION BA1 BA0 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 Address Bus W3E64M72S-XBX ADVANCED TABLE 1 - BURST DEFINITION Burst Length Starting Column Address A0 2 0 1 A1 0 4 0 1 1 A2 0 0 0 8 0 1 1 1 1 A1 0 0 1 1 0 0 1 1 A0 0 1 0 1 A0 0 1 0 1 0 1 0 1 0-1-2-3-4-5-6-7 1-2-3-4-5-6-7-0 2-3-4-5-6-7-0-1 3-4-5-6-7-0-1-2 4-5-6-7-0-1-2-3 5-6-7-0-1-2-3-4 6-7-0-1-2-3-4-5 7-0-1-2-3-4-5-6 0-1-2-3-4-5-6-7 1-0-3-2-5-4-7-6 2-3-0-1-6-7-4-5 3-2-1-0-7-6-5-4 4-5-6-7-0-1-2-3 5-4-7-6-1-0-3-2 6-7-4-5-2-3-0-1 7-6-5-4-3-2-1-0 0-1-2-3 1-2-3-0 2-3-0-1 3-0-1-2 0-1-2-3 1-0-3-2 2-3-0-1 3-2-1-0 0-1 1-0 0-1 1-0 Order of Accesses Within a Burst Type = Sequential Type = Interleaved 14 0* 13 0* 12 11 10 9 87 6 5 4 3 BT 2 1 0 Mode Register (Mx) Operating Mode CAS Latency Burst Length * M14 and M13 (BA0 and BA1 must be "0, 0" to select the base mode register (vs. the extended mode register). Burst Length M2 M1 M0 0 0 0 0 1 1 1 1 00 01 10 11 00 01 10 11 M3 = 0 Reserved 2 4 8 Reserved Reserved Reserved Reserved M3 = 1 Reserved 2 4 8 Reserved Reserved Reserved Reserved M3 0 1 Burst Type Sequential Interleaved M6 M5 M4 0 0 0 0 1 1 1 1 00 01 10 11 00 01 10 11 CAS Latency Reserved Reserved 2 Reserved Reserved Reserved 2.5 Reserved M12 0 0 - M11 0 0 - M10 0 0 - M9 0 0 - M8 0 1 - M7 0 0 - M6-M0 Valid Valid - Operating Mode Normal Operation Normal Operation/Reset DLL All other states reserved PRECHARGE is nonpersistent in that it is either enabled or disabled for each individual READ or WRITE command. The device supports concurrent auto precharge if the command to the other bank does not interrupt the data transfer to the current bank. AUTO PRECHARGE ensures that the precharge is initiated at the earliest valid stage within a burst. This "earliest valid stage" is determined as if an explicit precharge command was issued at the earliest possible time, without violating tRAS (MIN).The user must not issue another command to the same bank until the precharge time (tRP) is completed. NOTES: 1. For a burst length of two, A1-Ai select two-data-element block; A0 selects the starting column within the block. 2. For a burst length of four, A2-Ai select four-data-element block; A0-1 select the starting column within the block. 3. For a burst length of eight, A3-Ai select eight-data-element block; A0-2 select the starting column within the block. 4. Whenever a boundary of the block is reached within a given sequence above, the following access wraps within the block. recently registered READ command prior to the BURST TERMINATE command will be truncated. The open page which the READ burst was terminated from remains open. AUTO REFRESH AUTO REFRESH is used during normal operation of the DDR SDRAM and is analogous to CAS-BEFORE-RAS (CBR) REFRESH in conventional DRAMs. This command is nonpersistent, so it must be issued each time a refresh is required. All banks must be idle before an AUTO REFRESH command is issued. The addressing is generated by the internal refresh controller. This makes the address bits "Don't Care" BURST TERMINATE The BURST TERMINATE command is used to truncate READ bursts (with auto precharge disabled). The most June 2005 Rev. 0 White Electronic Designs Corp. reserves the right to change products or specifications without notice. 8 White Electronic Designs Corporation * (602) 437-1520 * www.wedc.com White Electronic Designs FIGURE 4 - CAS LATENCY T0 CLK# CLK COMMAND READ NOP CL = 2 DQS DQ NOP NOP T1 T2 T2n T3 T3n BA1 BA0 A12 A11 A10 A9 A8 A7 W3E64M72S-XBX ADVANCED FIGURE 5 - EXTENDED MODE REGISTER DEFINITION A6 A5 A4 A3 A2 A1 A0 Address Bus 14 13 12 11 10 9 8 01 11 7 6 5 4 3 2 1 0 Operating Mode DS DLL Extended Mode Register (Ex) E0 0 DLL Enable Disable Drive Strength Normal Reserved T0 CLK# CLK COMMAND READ T1 T2 T2n T3 T3n E1 1 NOP CL = 2.5 NOP NOP 0 1 DQS DQ E12 E11 E10 E9 E8 0 E7 0 E6 0 E5 0 E4 0 E3 0 E2 0 E1, E0 Valid Operating Mode Reserved Reserved Burst Length = 4 in the cases shown Shown with nominal tAC and nominal tDSDQ DATA TRANSITIONING DATA DON'T CARE 0 - 0 - 0 - 0 - 1. E14 and E13 must be "0, 1" to select the Extended Mode Register (vs. the base Mode Register) 2. The QFC# function is not supported. during an AUTO REFRESH command. Each DDR SDRAM requires AUTO REFRESH cycles at an average interval of 7.8125s (maximum). To allow for improved efficiency in scheduling and switching between tasks, some flexibility in the absolute refresh interval is provided. A maximum of eight AUTO REFRESH commands can be posted to any given DDR SDRAM, meaning that the maximum absolute interval between any AUTO REFRESH command and the next AUTO REFRESH command is 9 x 7.8125s (70.3s). This maximum absolute interval is to allow future support for DLL updates internal to the DDR SDRAM to be restricted to AUTO REFRESH cycles, without allowing excessive drift in tAC between updates. Although not a JEDEC requirement, to provide for future functionality features, CKE must be active (High) during the AUTO REFRESH period. The AUTO REFRESH period begins when the AUTO REFRESH command is registered and ends tRFC later. powered down. When in the self refresh mode, the DDR SDRAM retains data without external clocking. The SELF REFRESH command is initiated like an AUTO REFRESH command except CKE is disabled (LOW). The DLL is automatically disabled upon entering SELF REFRESH and is automatically enabled upon exiting SELF REFRESH (A DLL reset and 200 clock cycles must then occur before a READ command can be issued). Input signals except CKE are "Don't Care" during SELF REFRESH. VREF voltage is also required for the full duration of SELF REFRESH. The procedure for exiting self refresh requires a sequence of commands. First, CK and CK# must be stable prior to CKE going back HIGH. Once CKE is HIGH, the DDR SDRAM must have NOP commands issued for tXSNR, because time is required for the completion of any internal refresh in progress. A simple algorithm for meeting both refresh and DLL requirements is to apply NOPs for tXSNR time, then a DLL Reset and NOPs for 200 additional clock cycles before applying any other command. * Self refresh available in commercial and industrial temperatures only. SELF REFRESH* The SELF REFRESH command can be used to retain data in the DDR SDRAM, even if the rest of the system is White Electronic Designs Corp. reserves the right to change products or specifications without notice. June 2005 Rev. 0 9 White Electronic Designs Corporation * (602) 437-1520 * www.wedc.com White Electronic Designs TRUTH TABLE - COMMANDS (NOTE 1) NAME (FUNCTION) DESELECT (NOP) (9) NO OPERATION (NOP) (9) ACTIVE (Select bank and activate row) ( 3) READ (Select bank and column, and start READ burst) (4) WRITE (Select bank and column, and start WRITE burst) (4) BURST TERMINATE (8) PRECHARGE (Deactivate row in bank or banks) ( 5) AUTO REFRESH or SELF REFRESH (Enter self refresh mode) (6, 7) LOAD MODE REGISTER (2) CS# H L L L L L L L L RAS# X H L H H H L L L CAS# X H H L L H H L L W3E64M72S-XBX ADVANCED WE# X H H H L L L H L ADDR X X Bank/Row Bank/Col Bank/Col X Code X Op-Code TRUTH TABLE - DM OPERATION NAME (FUNCTION) WRITE ENABLE (10) WRITE INHIBIT (10) NOTES: 1. CKE is HIGH for all commands shown except SELF REFRESH. 2. A0-12 define the op-code to be written to the selected Mode Register. BA0, BA1 select either the mode register (0, 0) or the extended mode register (1, 0). 3. A0-12 provide row address, and BA0, BA1 provide bank address. 4. A0-9, 11 provide column address; A10 HIGH enables the auto precharge feature (non persistent), while A10 LOW disables the auto precharge feature; BA0, BA1 provide bank address. 5. A10 LOW: BA0, BA1 determine the bank being precharged. A10 HIGH: All banks precharged and BA0, BA1 are "Don't Care." DM L H 6. DQs Valid X This command is AUTO REFRESH if CKE is HIGH; SELF REFRESH if CKE is LOW. 7. Internal refresh counter controls row addressing; all inputs and I/Os are "Don't Care" except for CKE. 8. Applies only to read bursts with auto precharge disabled; this command is undefined (and should not be used) for READ bursts with auto precharge enabled and for WRITE bursts. 9. DESELECT and NOP are functionally interchangeable. 10. Used to mask write data; provided coincident with the corresponding data. White Electronic Designs Corp. reserves the right to change products or specifications without notice. June 2005 Rev. 0 10 White Electronic Designs Corporation * (602) 437-1520 * www.wedc.com White Electronic Designs ABSOLUTE MAXIMUM RATINGS Parameter Voltage on VCC, VCCQ Supply relative to Vss Voltage on I/O pins relative to Vss Operating Temperature TA (Mil) Operating Temperature TA (Ind) Operating Temperature TA (Com) Storage Temperature, Plastic Maximum Junction Temperature -1 to 3.6 -0.5V to VCCQ +0.5V -55 to +125 -40 to +85 -0 to +70 -55 to +125 125 W3E64M72S-XBX ADVANCED Unit V V C C C C C NOTE: Stress greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions greater than those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. CAPACITANCE (NOTE 13) Parameter Input Capacitance: CK/CK# Addresses, BA0-1 Input Capacitance Input Capacitance: All other input-only pins Input/Output Capacitance: I/Os Symbol CI1 CA CI2 CIO Max TBD TBD TBD TBD Unit pF pF pF pF BGA THERMAL RESISTANCE Description Junction to Ambient (No Airflow) Junction to Ball Junction to Case (Top) Symbol Theta JA Theta JB Theta JC Max TBD TBD TBD Units C/W C/W C/W Notes 1 1 1 Refer to "PBGA Thermal Resistance Correlation" (Application Note) at www.wedc.com in the application notes section for modeling conditions. White Electronic Designs Corp. reserves the right to change products or specifications without notice. June 2005 Rev. 0 11 White Electronic Designs Corporation * (602) 437-1520 * www.wedc.com White Electronic Designs VCC, VCCQ = +2.5V 0.2V; -55C TA +125C Symbol VCC VCCQ II II IOZ IOH IOL VREF VTT W3E64M72S-XBX ADVANCED DC ELECTRICAL CHARACTERISTICS AND OPERATING CONDITIONS (NOTES 1-5, 16) Parameter/Condition Supply Voltage (36, 41) I/O Supply Voltage (36, 41, 44) Input Leakage Current: Any one input 0V VIN VCC (All other pins not under test = 0V) Input Leakage Address Current (All other pins not under test = 0V) Output Leakage Current: I/Os are disabled; 0V VOUT VCCQ Output Levels: Full drive option (37, 39) High Current (VOUT = VCCQ - 0.373V, minimum VREF, minimum VTT) Low Current (VOUT = 0.373V, maximum VREF, maximum VTT) I/O Reference Voltage (6,44) I/O Termination Voltage (7, 44) Min 2.3 2.3 -2 -18 -5 -12 12 0.49 x VCCQ VREF - 0.04 Max 2.7 2.7 2 18 5 0.51 x VCCQ VREF + 0.04 Units V V A A A mA mA V V AC INPUT OPERATING CONDITIONS VCC, VCCQ = +2.5V 0.2V; -55C TA +125C Symbol VIH VIL Parameter/Condition Input High (Logic 1) Voltage Input Low (Logic 0) Voltage Min VREF +0.500 -- Max -- VREF -0.500 Units V V White Electronic Designs Corp. reserves the right to change products or specifications without notice. June 2005 Rev. 0 12 White Electronic Designs Corporation * (602) 437-1520 * www.wedc.com White Electronic Designs VCC, VCCQ = +2.5V 0.2V; -55C TA +125C W3E64M72S-XBX ADVANCED ICC SPECIFICATIONS AND CONDITIONS (NOTES 1-5, 10, 12, 14, 46) MAX Parameter/Condition OPERATING CURRENT: One bank; Active-Precharge; tRC = tRC (MIN); tCK = tCK (MIN); DQ, DM, and DQS inputs changing once per clock cyle; Address and control inputs changing once every two clock cycles; (22, 47) OPERATING CURRENT: One bank; Active-Read-Precharge; Burst = 2; tRC = tRC (MIN); tCK = tCK (MIN); IOUT = 0mA; Address and control inputs changing once per clock cycle (22, 47) PRECHARGE POWER-DOWN STANDBY CURRENT: All banks idle; Power-down mode; tCK = tCK (MIN); CKE = LOW; (23, 32, 49) IDLE STANDBY CURRENT: CS = HIGH; All banks idle; tCK = tCK (MIN); CKE = HIGH; Address and other control inputs changing once per clock cycle. VIN = VREF for DQ, DQS, and DM (50) ACTIVE POWER-DOWN STANDBY CURRENT: One bank active; Power-down mode; tCK = tCK (MIN); CKE = LOW (23, 32, 49) ACTIVE STANDBY CURRENT: CS = HIGH; CKE = HIGH; One bank; Active-Precharge; tRC = tRAS (MAX); tCK = tCK (MIN); DQ, DM, and DQS inputs changing twice per clock cycle; Address and other control inputs changing once per clock cycle (22) OPERATING CURRENT: Burst = 2; Reads; Continuous burst; One bank active; Address and control inputs changing once per clock cycle; tCK = tCK (MIN); IOUT = 0mA (22, 47) OPERATING CURRENT: Burst = 2; Writes; Continuous burst; One bank active; Address and control inputs changing once per clock cycle; tCK = tCK (MIN); DQ, DM, and DQS inputs changing twice per clock cycle (22) AUTO REFRESH CURRENT tREFC = tRC (MIN) (49) tREFC = 7.8125s (27, 49) SELF REFRESH CURRENT: CKE 0.2V Standard (11) Symbol 333Mbs 250Mbs/ 200Mbs 266Mbs ICC0 1,170 1,170 1,035 Units mA ICC1 ICC2P ICC2F ICC3P ICC3N 1,440 45 405 315 450 1,440 45 405 315 450 1,305 45 360 270 405 mA mA mA mA mA ICC4R ICC4W 1,485 1,755 1,485 1,440 1,305 1,215 mA mA ICC5 ICC5A ICC6 ICC7 2,610 90 45 3,645 2,610 90 45 3,645 2,520 90 45 3,510 mA mA mA mA OPERATING CURRENT: Four bank interleaving READs (BL=4) with auto precharge, tRC =tRC (MIN); tCK = tCK (MIN); Address and control inputs change only during Active READ or WRITE commands. (22, 48) White Electronic Designs Corp. reserves the right to change products or specifications without notice. June 2005 Rev. 0 13 White Electronic Designs Corporation * (602) 437-1520 * www.wedc.com White Electronic Designs Notes 1-5, 14-17, 33 333 Mbs CL3/CL2.5 (53) 266 Mbs CL2.5 Parameter Access window of DQs from CK/CK# CK high-level width (30) CK low-level width (30) Clock cycle time CL = 3 (45, 51) CL = 2.5 (45, 51) CL = 2 (45, 51) DQ and DM input hold time relative to DQS (26, 31) DQ and DM input setup time relative to DQS (26, 31) DQ and DM input pulse width (for each input) (31) Access window of DQS from CK/CK# DQS input high pulse width DQS input low pulse width DQS-DQ skew, DQS to last DQ valid, per group, per access (25, 26) Write command to first DQS latching transition DQS falling edge to CK rising - setup time DQS falling edge from CK rising - hold time Half clock period (34) Data-out high-impedance window from CK/CK# (18, 42) Data-out low-impedance window from CK/CK# (18, 42) Address and control input hold time (fast slew rate) Address and control input setup time (fast slew rate) Address and control input hold time (slow slew rate) (14) Address and control input setup time (slow slew rate) (14) LOAD MODE REGISTER command cycle time DQ-DQS hold, DQS to first DQ to go non-valid, per access (25, 26) Data hold skew factor ACTIVE to PRECHARGE command (35) ACTIVE to READ with Auto precharge command ACTIVE to ACTIVE/AUTO REFRESH command period AUTO REFRESH command period (49) ACTIVE to READ or WRITE delay PRECHARGE command period DQS read preamble (43) DQS read postamble (43) ACTIVE bank a to ACTIVE bank b command DQS write preamble DQS write preamble setup time (20, 21) DQS write postamble (19) Write recovery time Internal WRITE to READ command delay Data valid output window (25) REFRESH to REFRESH command interval (23) (Commercial & Industrial only) REFRESH to REFRESH command interval (23) (Military temperature only)* Average periodic refresh interval (23) (Commercial & Industrial only) Average periodic refresh interval (23) (Military temperature only)* Terminating voltage delay to VDD Exit SELF REFRESH to non-READ command Exit SELF REFRESH to READ command * Self refresh available in commercial and industrial temperatures only. White Electronic Designs Corp. reserves the right to change products or specifications without notice. June 2005 Rev. 0 14 Symbol tAC tCH tCL tCK (3) tCK (2.5) tCK (2) tDH tDS tDIPW tDQSCK tDQSH tDQSL tDQSQ tDQSS tDSS tDSH tHP tHZ tLZ tIHF tISF tIHS tISS tMRD tQH tQHS tRAS tRAP tRC tRFC tRCD tRP tRPRE tRPST tRRD tWPRE tWPRES tWPST tWR tWTR na tREFC tREFC tREFI tREFI tVTD tXSNR tXSRD 0 75 200 42 15 60 72 15 15 0.9 0.4 12 0.25 0 0.4 15 1 tQH - tDQSQ 70.3 35 7.8 3.9 0 75 200 0.6 1.1 0.6 -0.70 0.75 0.75 0.8 0.8 12 tHP-tQHS 0.55 70,000 40 20 65 75 20 20 0.9 0.4 15 0.25 0 0.4 15 1 tQH - tDQSQ 70.3 35 7.8 3.9 0.6 1.1 0.6 0.75 0.2 0.2 tCH,tCL +0.70 -0.75 0.90 0.90 1 1 15 tHP-tQHS 0.75 120,000 Min -0.70 0.45 0.45 6 7.5 10 0.45 0.45 1.75 -0.6 0.35 0.35 0.45 1.25 0.75 0.2 0.2 tCH,tCL +0.75 +0.6 Max +0.70 0.55 0.55 13 13 13 7.5 10 0.5 0.5 1.75 -0.75 0.35 0.35 0.5 1.25 +0.75 13 13 266 Mbs CL2.5 200 CL2 Min -0.75 0.45 0.45 Max +0.75 0.55 0.55 W3E64M72S-XBX ADVANCED ELECTRICAL CHARACTERISTICS AND RECOMMENDED AC OPERATING CHARACTERISTICS 250 Mbs CL2.5 200 Mbs CL2 Min -0.8 0.45 0.45 8 10 0.6 0.6 2 -0.8 0.35 0.35 0.6 0.75 0.2 0.2 tCH,tCL +0.8 -0.8 1.1 1.1 1.1 1.1 16 tHP-tQHS 1 40 20 70 80 20 20 0.9 0.4 15 0.25 0 0.4 15 1 tQH - tDQSQ 70.3 35 7.8 3.9 0 80 200 0 80 200 0.6 1.1 0.6 120,000 40 20 70 80 20 20 0.9 0.4 15 0.25 0 0.4 15 1 tQH - tDQSQ 70.3 35.15 7.8 3.9 0.6 1.1 0.6 -0.8 1.1 1.1 1.1 1.1 16 tHP-tQHS 1 120,000 1.25 0.75 0.2 0.2 tCH,tCL +0.8 +0.8 Max +0.8 0.55 0.55 13 13 200 Mbs CL2.5 150 Mbs CL2 Min -0.8 0.45 0.45 10 13 0.6 0.6 2 -0.8 0.35 0.35 0.6 1.25 +0.8 Max +0.8 0.55 0.55 13 15 Units ns tCK tCK ns ns ns ns ns ns ns tCK tCK ns tCK tCK tCK ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns tCK tCK ns tCK ns tCK ns tCK ns s s s s ns ns tCK White Electronic Designs Corporation * (602) 437-1520 * www.wedc.com White Electronic Designs NOTES: 1. All voltages referenced to VSS. 2. Tests for AC timing, ICC, and electrical AC and DC characteristics may be conducted at nominal reference/supply voltage levels, but the related specifications and device operation are guaranteed for the full voltage range specified. 3. Outputs measured with equivalent load: 50 Output (VOUT) VTT W3E64M72S-XBX ADVANCED 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. AC timing and ICC tests may use a VIL-to-VIH swing of up to 1.5V in the test environment, but input timing is still referenced to VREF (or to the crossing point for CK/CK#), and parameter specifications are guaranteed for the specified AC input levels under normal use conditions. The minimum slew rate for the input signals used to test the device is 1V/ns in the range between VIL(AC) and VIH(AC). The AC and DC input level specifications are as defined in the SSTL_2 Standard (i.e., the receiver will effectively switch as a result of the signal crossing the AC input level, and will remain in that state as long as the signal does not ring back above [below] the DC input LOW [HIGH] level). VREF is expected to equal VCCQ/2 of the transmitting device and to track variations in the DC level of the same. Peak-to-peak noise (noncommon mode) on VREF may not exceed 2 percent of the DC value. Thus, from VCCQ/2, VREF is allowed 25mV for DC error and an additional 25mV for AC noise. This measurement is to be taken at the nearest VREF by-pass capacitor. VTT is not applied directly to the device. VTT is a system supply for signal termination resistors, is expected to be set equal to VREF and must track variations in the DC level of VREF. VID is the magnitude of the difference between the input level on CK and the input level on CK#. The value of VIX and VMP are expected to equal VCCQ/2 of the transmitting device and must track variations in the DC level of the same. ICC is dependent on output loading and cycle rates. Specified values are obtained with minimum cycle time with the outputs open. Enables on-chip refresh and address counters. ICC specifications are tested after the device is properly initialized, and is averaged at the defined cycle rate. This parameter is not tested but guaranteed by design. tA = 25C, F= 1 MHz For slew rates less than 1V/ns and greater than or equal to 0.5 V.ns. If the slew rate is less than 0.5V/ns, timing must be derated: tIS has an additional 50 ps per each 100mV/ns reduction in slew rate from the 500mV/ns. tIH has 0ps added, that is, it remains constant. If the slew rate exceeds 4.5V/ns, functionality is uncertain. 15. The CK/CK# input reference level (for timing referenced to CK/CK#) is the point at which CK# and CK# cross; the input reference level for signals other than CK/CK# is VREF. 16. Inputs are not recognized as valid until VREF stabilizes. Once initialized, including SELF REFRESH mode, VREF must be powered within specified range. Exception: during the period before VREF stabilizes, CKE 0.3 x VCCQ is recognized as LOW. 17. The output timing reference level, as measured at the timing reference point indicated in Note 3, is VTT. 18. tHZ and tLZ transitions occur in the same access time windows as valid data transitions. These parameters are not referenced to a specific voltage level, but specify when the device output is no longer driving (HZ) or begins driving (LZ). 19. The intent of the Don't Care state after completion of the postamble is the DQSdriven signal should either be high, low, or high-Z and that any signal transition within the input switching region must follow valid input requirements. That is, if DQS transitions high (above VIHDC(MIN) then it must not transition low (below VIHDC) prior to tDQSH(MIN). 20. This is not a device limit. The device will operate with a negative value, but system performance could be degraded due to bus turnaround. 21. It is recommended that DQS be valid (HIGH or LOW) on or before the WRITE command. The case shown (DQS going from High-Z to logic LOW) applies when no WRITEs were previously in progress on the bus. If a previous WRITE was in progress, DQS could be HIGH during this time, depending on tDQSS. 22. MIN (tRC or tRFC) for ICC measurements is the smallest multiple of tCK that meets the minimum absolute value for the respective parameter. tRAS (MAX) for ICC measurements is the largest multiple of tCK that meets the maximum absolute value for tRAS. 23. The refresh period 64ms. (32ms for Military grade) This equates to an average refresh rate of 7.8125s. However, an AUTO REFRESH command must be asserted at least once every 70.3s; (35s for Military grade) burst refreshing or posting by the DRAM controller greater than eight refresh cycles is not allowed. 24. The I/O capacitance per DQS and DQ byte/group will not differ by more than this maximum amount for any given device. 25. The valid data window is derived by achieving other specifications - tHP (tCK/2), tDQSQ, and tQH (tQH = tHP - tQHS). The data valid window derates directly porportional with the clock duty cycle and a practical data valid window can be derived. The clock is allowed a maximum duty cycle variation of 45/55. Functionality is uncertain when operating beyond a 45/55 ratio. The data valid window derating curves are provided below for duty cycles ranging between 50/50 and 45/55. 26. Referenced to each output group: DQSL with DQ0-DQ7; and DQSH with DQ8DQ15 of each chip. FIGURE A FULL DRIVE PULL-DOWN CHARACTERISTICS 160 140 FIGURE B FULL DRIVE PULL-UP CHARACTERISTICS 0 -20 -40 Maximum Minimum Nominal low 120 -60 Nominal high 100 IOUT (mA) IOUT (mA) -80 -100 -120 -140 -160 80 Nominal low 60 Nominal high Minimum 40 20 -180 -200 Maximum 0 0.0 0.5 1.0 1.5 2.0 2.5 0.0 0.5 1.0 1.5 2.0 2.5 VOUT (V) VCCQ - VOUT (V) White Electronic Designs Corp. reserves the right to change products or specifications without notice. June 2005 Rev. 0 15 White Electronic Designs Corporation * (602) 437-1520 * www.wedc.com White Electronic Designs 27. This limit is actually a nominal value and does not result in a fail value. CKE is HIGH during REFRESH command period (tRFC [MIN]) else CKE is LOW (i.e., during standby). 28. To maintain a valid level, the transitioning edge of the input must: a) Sustain a constant slew rate from the current AC level through to the target AC level, VIL(AC) or VIH(AC). b) Reach at least the target AC level. c) After the AC target level is reached, continue to maintain at least the target DC level, VIL(DC) or VIH(DC). 29. The Input capacitance per pin group will not differ by more than this maximum amount for any given device. 30. CK and CK# input slew rate must be 1V/ns (2V/ns differentially). 31. DQ and DM input slew rates must not deviate from DQS by more than 10%. If the DQ/DM/DQS slew rate is less than 0.5V/ns, timing must be derated: 50ps must be added to tDS and tDH for each 100mV/ns reduction in slew rate. If slew rate exceeds 4V/ns, functionality is uncertain. 32. VCC must not vary more than 4% if CKE is not active while any bank is active. 33. The clock is allowed up to 150ps of jitter. Each timing parameter is allowed to vary by the same amount. 34. tHP min is the lesser of tCL minimum and tCH minimum actually applied to the device CK and CK# inputs, collectively during bank active. 35. READs and WRITEs with auto precharge are not allowed to be issued until tRAS(MIN) can be satisfied prior to the internal precharge command being issued. 36. Any positive glitch must be less than 1/3 of the clock and not more than +400mV or 2.9 volts, whichever is less. Any negative glitch must be less than 1/3 of the clock cycle and not exceed either -300mV or 2.2 volts, whichever is more positive. The average cannot be below the 2.5V minimum. 37. Normal Output Drive Curves: a) The full variation in driver pull-down current from minimum to maximum process, temperature and voltage will lie within the outer bounding lines of the V-I curve of Figure A. b) The variation in driver pull-down current within nominal limits of voltage and temperature is expected, but not guaranteed, to lie within the inner bounding lines of the V-I curve of Figure A. c) The full variation in driver pull-up current from minimum to maximum process, temperature and voltage will lie within the outer bounding lines of the V-I curve of Figure B. d) The variation in driver pull-up current within nominal limits of voltage and temperature is expected, but not guaranteed, to lie within the inner bounding lines of the V-I curve of Figure B. e) The full variation in the ratio of the maximum to minimum pull-up and pull-down current should be between .71 and 1.4, for device drain-to-source voltages from 0.1V to 1.0 Volt, and at the same voltage and temperature. f) The full variation in the ratio of the nominal pull-up to pull-down current should be unity 10%, for device drain-to-source voltages from 0.1V to 1.0 Volt. W3E64M72S-XBX ADVANCED 38. NA 39. The voltage levels used are derived from a minimum VCC level and the referenced test load. In practice, the voltage levels obtained from a properly terminated bus will provide significantly different voltage values. 40. VIH overshoot: VIH(MAX) = VCCQ+1.5V for a pulse width 3ns and the pulse width can not be greater than 1/3 of the cycle rate. VIL undershoot: VIL (MIN) = -1.5V for a pulse width 3ns and the pulse width cannot be greater than 1/3 of the cycle rate. 41. VCC and VCCQ must track each other. 42. tHZ (MAX) will prevail over tDQSCK (MAX) + tRPST (MAX) condition. tLZ (MIN) will prevail over tDQSCK (MIN) + tRPRE (MAX) condition. 43. tRPST end point and tRPRE begin point are not referenced to a specific voltage level but specify when the device output is no longer driving (tRPST), or begins driving (tRPRE). 44. During initialization, VCCQ, VTT, and VREF must be equal to or less than VCC + 0.3V. Alternatively, VTT may be 1.35V maximum during power up, even if VCC/VCCQ are 0 volts, provided a minimum of 42 ohms of series resistance is used between the VTT supply and the input pin. 45. The current part operates below the slowest JEDEC operating frequency of 83 MHz. As such, future die may not reflect this option. 46. When an input signal is HIGH or LOW, it is defined as a steady state logic HIGH or LOW. 47. Random addressing changing: 50% of data changing at every transfer. 48. Random addressing changing: 100% of data changing at every transfer. 49. CKE must be active (high) during the entire time a refresh command is executed. That is, from the time the AUTO REFRESH command is registered, CKE must be active at each rising clock edge, until tRFC has been satisfied. 50. ICC2N specifies the DQ, DQS, and DQM to be driven to a valid high or low logic level. ICC2Q is similar to ICC2F except ICC2Q specifies the address and control inputs to remain stable. Although ICC2F, ICC2N, and ICC2Q are similar, ICC2F is "worst case." 51. Whenever the operating frequency is altered, not including jitter, the DLL is required to be reset followed by 200 clock cycles before any READ command. 52. This is the DC voltage supplied at the DRAM and is inclusive of all noise up to 20 MHz. Any noise above 20 MHz at the DRAM generated from any source other than that of the DRAM itself may not exceed the DC coltage range of 2.6V 100mV. 53. For 333Mbs operation of Industrial and commercial temperatures CL = 2.5, at Military temperature CL = 3. White Electronic Designs Corp. reserves the right to change products or specifications without notice. June 2005 Rev. 0 16 White Electronic Designs Corporation * (602) 437-1520 * www.wedc.com White Electronic Designs W3E64M72S-XBX ADVANCED PACKAGE DIMENSION: 219 PLASTIC BALL GRID ARRAY (PBGA) BOTTOM VIEW 32.1 (1.264) MAX 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 T R P N M L K J 25.1 (0.988) H MAX G F E D C B A 0.61 (0.024) NOM 2.96 (0.116) MAX 19.05 (0.750) NOM 1.27 (0.050) NOM 219 x O 0.762 (0.030) NOM 19.05 (0.750) NOM ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES White Electronic Designs Corp. reserves the right to change products or specifications without notice. June 2005 Rev. 0 17 White Electronic Designs Corporation * (602) 437-1520 * www.wedc.com White Electronic Designs ORDERING INFORMATION W3E64M72S-XBX ADVANCED W 3E 64M 72 S - XXX B X WHITE ELECTRONIC DESIGNS CORP. DDR SDRAM CONFIGURATION, 64M x 72 2.5V Power Supply DATA RATE (Mbs) 200 = 200Mbs 250 = 250Mbs 266 = 266Mbs 333 = 333Mbs PACKAGE: ES = Non Qualified Product (1) B = 219 Plastic Ball Grid Array (PBGA) DEVICE GRADE: M = Military I = Industrial C = Commercial -55C to +125C -40C to +85C 0C to +70C Note 1: W3E64M72S-ESB is the only available product until completion of qualification. White Electronic Designs Corp. reserves the right to change products or specifications without notice. June 2005 Rev. 0 18 White Electronic Designs Corporation * (602) 437-1520 * www.wedc.com White Electronic Designs Document Title 64M x 72 DDR SDRAM 219 PBGA Multi-Chip Package W3E64M72S-XBX ADVANCED Revision History Rev # Rev 0 History Initial Release Release Date June 2005 Status Advanced White Electronic Designs Corp. reserves the right to change products or specifications without notice. June 2005 Rev. 0 19 White Electronic Designs Corporation * (602) 437-1520 * www.wedc.com |
Price & Availability of W3E64M72S-266ESC
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |